DELUXE TRAVEL FOLDING 2-BOW BIMINI TOP for INFLATABLE BOAT W/ free BAG

Description

NO SHIPPING TO HAWAII, PUERTO  RICO, ALASKA. SHIPPING VIA FEDEX GROUND ONLY
TO LOWER 48 STATES OF CONTINENTAL US.  NO SHIPPING TO PO BOX.
https://youtu.be/RmkMDxPky_U
Deluxe Travel Folding 2-Bow Sun Canopy Bimini Tops for Inflatable Boat
Type: 2 bow (Folding, assembled with pushpin)
Fit from: 47" to 76" between attachment points.
That means that support poles can be pushed together as close as 47"  or pushed apart as far as 76".
Dimensions: 70" long x 55" wide x 46" high.
Protect yourself from Sun and rain with our deluxe sun canopy. Fits on  most inflatable boats. With easy DIY alteration also will fit on KaBoats.  Breaks down into small carry bag!
Make your inflatable boat riding experience even more comfortable and  protect yourself from harsh ultraviolet rays with a Saturn Deluxe  Folding 2-Bow Bimini Top Canopy. No need to use screws. Easy assembly  with pushpin. Breaks down into storage bag for easy storage and portable  transportation.
Deluxe Folding Sun/Rain Canopies come in light gray color and very easy  to install. It
keeps  you cool and protected from the harmful UV rays of the sun and  unexpected rain. The 600 deniers PVC Coated polyester canopy and folding  aluminum tubing. Fits many sizes of boats with pined oarlocks,
splash  guards or hugging rope holders.
Deluxe 2-bow canopy has two support poles on each side which form a V,  and anchors to the oar locks with provided clips, or splash guard  grommets near the center of the boat. The 2-bow canopy is held in place  by 4 bow lines, two center brackets, and two stern lines. Support poles  has some flex to it, and can be pushed up to several inches inward or  outward, to fit between 47" and 76" of installation points.
But, this top can be also installed on more narrow boats, such as  KaBoats and even kayaks. To make this top more narrow, simply cut top  tubes shorter on one or both sides, and re-drill new holes for pushpins.  It is easy, 5 minutes DIY project. Just need hacksaw and electric drill.  See Assembly Steps below.
Deluxe Folding 2-Bow Sun Shade Top Specifications:
Installs easily with snap pushpins.
Protects from heat and rain.
Rugged, waterproof reinforced canopy top.
1" anodized aluminum frame with stainless steel screws.
Make your boat look really cool and sporty.
Can be used while riding boat.
All necessary hardware is included.
Shipping size: 32.5 x 14.5 x 3"
Glue-on mounting patches optional.
Bonus: storage boot included!
Bonus: carry bag included!
Deluxe 2-bow canopy installation suggestion: READ BELOW AND SEE PICTURES.
Deluxe 2-bow canopies may be attached directly to the grommets that are  installed into splash guard on top of the boat tubes.
Plastic cable ties can be run through the support pole holes and grommets in  the splash guard or optional wing nut bolts can be used for quick  disconnect.
Four straps can also be secured to grommets in a same manner.
Properly adjusted tension of strap lines will hold the canopy vertically in  place.
To fold canopy down, simply unlock straps in front or in rear and fold  canopy down.
Canopy support poles can also be mounted on top of tubes with provided  glue-on patches.
If no attachment places are available at all, then D-rings need to be glued  on top of tubes in order to provide attachment points.
To make installation easier on a more narrow boat, push one end of support  poles against some object, and then push on another end of pole, to bring it  to desirable distance, then use rope to tighten both poles together. Install  bimini and then remove rope
PLEASE NOTE: Canopy comes with standard hardware for installation on fiberglass  or aluminium boat. When installing on inflatable boat, some of these hardware  can be discarded. Canopy support poles can be installed directly on oarlocks. To  fit over pin of oarlock, holes on plastic mounting jaws need to be enlarged or  drilled directly into aluminium.
Rowing oars can be placed on top of oarlocks and fastened with a rubber cord. If  you need to use oars, just fold the canopy toward the bow, unscrew the pins and  remove the poles from oarlocks. Move the folded canopy a couple of inches toward  the bow and install oars onto the pins of oar locks.
If pinned oarlocks are not available, as in SD430 or SD470 for example, then  aluminium support poles of 4-bow canopies may be attached directly to the splash  guard protectors on top of the boat tubes. Plastic ties can be run through the  support pole holes and rope holes in the splash guard. Properly adjusted lines  will hold the canopy in place. Click on pictures below to zoom in.
If no points to attach support poles to top of tubes inflatable boat are  available, then D-rings or some other grab-on contraption need to be glued.
PLEASE, PAY BY PAYPAL TO  CONFIRM ADDRESS ONLY AND  READ DESCRIPTION CAREFUL
IF RETURN, YOU HAVE TO  PAY SHIPPING and Item  must be not opened,  not used and sent back  in condition as was  shipped. Refund will be  issued after inspection  returned product